﻿ hdpe coefficient of friction table

# hdpe coefficient of friction table

### DESIGN COEFFICIENT TABLES - CECALC.com

DESIGN COEFFICIENT TABLES Hazen-Williams Friction Factor (C) Pipe Material Values for C Range High/Low Average Value Typical Design Value Plastic, PVC, Polyethylene pipe or tubing 160/150 150-155 150 Cement or mastic lined iron or steel pipe 160/130 148 140 Copper, brass, lead, tin or glass pipe or tubing 150/120 140 130

Get Price

### Coefficient of Friction Equation and Table Chart - Engineers Edge

Static friction is friction between two or more solid objects that are not moving relative to each other. For example, static friction can prevent an object from sliding down a sloped surface. The coefficient of static friction, typically denoted as μ s , is usually higher than the coefficient of kinetic friction.

Get Price

### HDPE Data Sheet - Direct Plastics

Coefficient of friction against hardened and ground steel P= 0.05 N/mm2, v= 0.6m/s 0.29 - - Ball indentation hardness 43 MPa 2039 -1 Shore hardness D 64 - 868 Thermal Properties Value Unit DIN/EN/ISO Glass transition temperature -95 °C 537 36 Crystalline m elting point 130 °C 537 36

Get Price

### Pacific Pump and Power

Note: HDPE is commonly sized by outside diameter. If in doubt, use the next smaller pipe size. Pipe Diameter (Inch) Flow (GPM) Head Loss / 100 Feet Pipe Due to Friction (C = 150) Friction Loss Table C = 150 for High Density Polyethylene Pipe (HDPE) Page 2

Get Price

### Friction Loss Tables For Hdpe Pipe | Brokeasshome.com

Friction Loss Tables For Hdpe Pipe Craig Mentzer October 13, 2017 Uncategorized Leave a comment 260 Views Pvc pipes schedule 40 friction loss pipe roughness coefficients table hdpe design con siderations chapter 6 design of pe piping systems

Get Price

### Hazen-Williams Coefficients - Engineering ToolBox

Plastic Pipes - Friction Head Loss - Friction head loss (ft/100 ft) in plastic pipes - PVC, PP, PE, PEH Tag Search en: hazen-williams coefficients factors pipe tube

Get Price

### Pipe Roughness Coefficients Table Charts | Hazen-Williams .

Relative roughness and friction factors for new, clean pipes for flow of 60°F (15.6°C) water (Hydraulic Institute Engineering Data Book, Reference 5) (1 meter 39.37 in = 3.28 ft). Where: f = friction factor

Get Price

### Pacific Pump and Power

Note: HDPE is commonly sized by outside diameter. If in doubt, use the next smaller pipe size. Pipe Diameter (Inch) Flow (GPM) Head Loss / 100 Feet Pipe Due to Friction (C = 150) Friction Loss Table C = 150 for High Density Polyethylene Pipe (HDPE) Page 2

Get Price

### Friction Loss Tables For Hdpe Pipe | Brokeasshome.com

Friction Loss Tables For Hdpe Pipe Craig Mentzer October 13, 2017 Uncategorized Leave a comment 260 Views Pvc pipes schedule 40 friction loss pipe roughness coefficients table hdpe design con siderations chapter 6 design of pe piping systems

Get Price

### Appendix A: Friction Losses for Water Flow Through Pipe

lower value is typically used. For HDPE pipe, a range of C values between 150 and 160 is typical. Tables A.1 and A.2 show friction loss data calculated by the Hazen Williams formula for the most commonly used steel and PVC pipe diameters, based on C values of 140 and 150, respectively. It should be noted that steel and PVC pipe

Get Price

### Pipe Roughness Coefficients Table Charts | Hazen-Williams .

Relative roughness and friction factors for new, clean pipes for flow of 60°F (15.6°C) water (Hydraulic Institute Engineering Data Book, Reference 5) (1 meter 39.37 in = 3.28 ft). Where: f = friction factor

Get Price

### (PDF) Friction Behavior of High Density Polyethylene (HDPE .

Table I. Mechanical properties of HDPE in the 0 . The friction coefficient of the PI in slight wear was stable. In the medium wear and severe regions, the friction coefficients of the Pl varied .

Get Price

### PLASTIC PROPERTY COMPARISON GRAPH - Fabrication

P PBT UHMW PTFE ABS PC PPO PSU PEI PEEK PPS PAI PI HDPE PP PVC Coefficient of Friction (Seven Trustr has less friction) 0 2 4 6 8 10 12 14 16 PA 6/6 PA 6 POM H ‐ C PET ‐ P PBT UHMW PTFE ABS PC PPO PSU PEI PEEK PPS PAI PI HDPE PP PVC Impact Strength (Ft.‐lb/inch of notch ‐Higher is better) 0 0.2 0.4 0.6 0.8 1 PA 6/6 PA ‐ 6 POM H ‐ C PET ‐

Get Price